Configuring the Citrix XML Service Port配置citrix xml 服務端口
XenApp uses the Citrix XML Service to supply the Web Interface server, and its connecting clients, with the names of applications available in a farm. By default, Setup configures the Citrix XML Service to share the default TCP/IP communication port (port 80) with Microsoft Internet Information Services (IIS).
xenapp用 citrix xml service連接web interface 服務器與farm中應用程序間通信，并為客戶端連接提供連接支持。默認情況下，安裝程序會配置citrix xml service 與iis共享tcp/ip默認通信端口（80）。
If you intend to send data to the Web Interface over a secure HTTP connection using SSL, be sure that the Citrix XML Service is set to share its port with IIS and that IIS is configured to support HTTPS. If you intend to install the Web Interface on the same server as the XML service, select the port sharing option.
如果你打算使用ssl建立安全http連接傳輸數據到web interface，確認citrix xml service 與iis使用共享端口，并且iis已經被配置支持https連接。如果你打算把web interface和xml service安裝到同一臺服務器上，選擇端口共享選項。
The Configure Citrix XML Service Port page, where you configure the XML Service in Setup, has two options:
Share default TCP/IP port with Internet Information Services.
(Default.) If you select this option, the XML Service communicates over whatever you configured IIS to communicate over. By default, IIS communicates over port 80 for HTTP traffic and, if configured, port 443 for HTTPS traffic. A common scenario when you would want to select this option is if you have the Web Interface and XenApp installed on the same server.
與iis共享默認TCP/IP端口
如果你選擇此項，xml service通信配置將隨iis配置改變而改變。默認情況下，iis為http鏈路使用80端口通信，也可以通過配置，為https鏈路使用443端口通信。如果把web interface和xenapp裝在一臺服務器上，通常選擇此項——共享端口。
If you choose to share a port between IIS and the XML Service and you want to change the XML Service port after installation, you must do so manually. There is no option on the Server Properties > XML Service page.
如果你選擇共享端口，但在安裝后想更改xml service端口，必須手動更改設置。在server properties > xml service page沒有相應的選項。
You can run the XML service over port 443 using SSL in two ways:
Configure IIS for HTTPS traffic on port 443, and choose port sharing in XenApp Setup.
Configure SSL relay on port 443. It does not matter whether you choose port sharing or not.
Note: If you want the XML service to share a port with IIS, you must install the Web Interface before running XenApp Setup.
你有兩種方法在443端口上運行xml service（使用ssl）：
在443端口上為https鏈路配置iis，在xenapp安裝中選擇端口共享
在443端口上配置ssl中繼，無論是否選擇端口共享，都沒有關系
Use a separate port.
Opens a different port number on the XenApp server for the XML Service’s communications with the Web Interface and the clients. Select this option if you:
Want to install the XML Service on a dedicated XML server
Do not want the Citrix XML Service to share the TCP port with IIS
If, during Setup, you plan to specify a port number other than the default, make sure other applications do not use the new port number. For a list of ports in use, type netstat -a at a command prompt. Make a note of the port number you specify. If you change the default port, configure Web Interface servers and any clients connecting to it to use the new port number.
Important: All servers in the farm must use the same TCP port for the Citrix XML Service.
使用獨立端口
在xenapp 服務器上，為xml service和webinterface以及客戶端間的通信開發一個不同的端口號，如果你是下列情況可以選擇此項：
想要吧xml service安裝在一臺指定的xml服務器少年宮
不想與iis共享端口
如果在安裝過程中，你打算不使用么人端口而是自己指定一個端口號，一定要確定其他應用程序沒有在使用這個新端口?？梢栽诿畲翱谥休斎雗etstat -a 來查看使用中的端口列表。記錄下你選擇的端口號。如果你改變了默認端口號，要在配置web interface 服務器和為客戶端建立連接時使用這個新端口號。
重要：farm中的所有服務器xml service必須使用相同的tcp端口號
